VideoTrak IQ
Combining high sensitivity in all lighting conditions with high resolution imagery
Request information
Oriux’s Color Video Detection Camera is a rugged, high performance video camera designed for use with the VideoTrak-IQ Detection System. This camera is the perfect source to feed images into the patented digital image processing algorithms of your Oriux video traffic detection system.
Zoom/Focus over coax eliminates the need to ever open the camera housing. Built-in intelligence allows the camera to adjust to all lighting conditions which ensures the VideoTrak-IQ receives the highest quality images possible in all traffic environments.
Features
Features
Camera
- Imager: 1/4 Color CCD - 380,000
- Lens: Pixels (Sony) 18X Zoom - f = 4.1mm (wide) to 73.8mm (tele) - F1.4 to F3.0 - Horizontal Viewing Angle 48 to 2.8’
- Zoom/Focus Control: 12VDC (Or over Coax) 1.0lx (50db)
- Sensitivity: Greater than 50db
- Signal to Noise Video Connector: NTSC 1 .OVp-p Color - Single 16-pin MilSpec connector combines power, video and zoom control
- Weight: 4 lbs. 14 oz. (2.21 kg)
- Dimensions: 11.7" (297 mm) Length - 4.41" (112mm) Height (Not including sunshield)
- Environmental: Temperature -37’ C to +74’C (-35* F to+165’ F) 0% to 100% Relative Humidity
- Power: 115 VAC, -20W (Heater On), - 5W (Heater Off)
Card
- Power Consumption: {4 channel VideoTrak-IQ} - 540mA @ 12V (6.5W) - 290mA @ 24V (7.0W)
- Voltage: 10-26 VDC
- Temperature Standards compliance: -NEMATS1/TS2, CALTRANS - 170/179 or 2070 ATC
- Environmental: -40C to +85C (-40F to +185F)
- Dimensions: Height: 4.50 (114.3mm) - Width: 2.34 (59.4mm) - Depth: 6.88 (174.7mm) - Handle: 1.09 (27.6mm)
- Ordering Information: One Camera Video Input - # 90-180-05 - Two Camera Video Inputs - it 90-180-06 - Three Camera Video Inputs - # 90-180-07 - Four Camera Video Inputs - # 90-180-08 - ** One Camera Video Input - # 90-180-01 - ** (No SDLC Single Slot Video Card)
- SDLC communication port allows direct connection for all TS2 environments which also makes available up to 64 output assignments and 16 phase color inputs
- Two USB 2.0 connections allow one to be used for a mouse while the other is being used to save system configurations via a Flash Drive. It can also be used to upload new Firmware and Upgrades as they become available
- Aux I/O connector provides an additional 8 outputs, 4 inputs, and allows for direct wiring to cabinet terminals or connection to extender cards for routing detectors to other rack slots
- Ethernet Port - Units are “IP-Addressable allowing video streaming for hi quality remote monitoring and configuration adjustments
- A three color status LED for each video channel
- Edge output status LED's 1 - 4
- Standard RCA
Benefits
Benefits
Camera
- Simple installation - no need to ever open housing
- Zoom and focus controls are adjusted at the cabinet using the existing coaxial video connector
- Autofocus automatically follows any zoom command eliminating the need for manual focus operation which reduces the risk for poor night focus
- Camera provides full color / motorized zoom focus control - with autofocus and manual focus override
- 18 Times zoom lens is more than adequate for adjusting the image for optimum video detection over several lanes
- High sensitivity camera - designed to provide optimum image in all lighting conditions
- Full color camera designed to complement VideoTrak-IQ and is compatible with previous generation Peek video products
- While the camera is smaller and lighter it retains the same bracket, connector and pin-out design, to make it reverse compatible with existing Oriux installations
- Camera sled (cradle) can be rolled through 360 degrees (to provide level adjustment of image)
- Designed to meet NEMA and FCC Class B, part 15 requirements.
Card
- A Four camera video detection card in the space of a single four channel loop detector card
- No PC required for setup - Just a mouse and a monitor
- Individual zone settings include: Sensitivity, shadow filtering, zone delay/extend, and vehicle directionality
- Front or rear video inputs
- Internal flash memory for saving configuration file directly to the card
- Card edge connector includes 4 outputs and 2 conditional inputs
- Card is selectable to be fully compliant with NEMA or CALTRANS standards
- Event Log for viewing system events with date I time stamp
- Battery backed Real Time Clock
- 12 outputs, 6 inputs
